Or Book Technician Here

 

 

This article following next on the subject of How to Install a Bathtub Yourself is exceedingly stimulating. You should give it a look.

Setting up a bath tub isn't precisely rocket science, however it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably challenging task. If the old tub is conveniently available, the task can move immediately; if you have to open a wall surface to get rid of the old tub as well as place the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the brand-new one. Ensure you have actually qualified on your own for the task and also fit attempting it. Instead of employing a specialist to take control of a halfway-completed task, it is better to think about utilizing one prior to you start. Chances are you may need an expert plumber to make tube links.
This write-up will certainly aid you install a new bathtub in your shower room if you have already gotten a brand-new bathtub and also do not require to transform the setup of your previous water supply pipelines.
Your tools and material list must make up the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Getting ready for the Installment

To start with, the sustaining framework provided with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps utilizing 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should now be ready to be suited its last setting.

 

 

Removing Old Taps

If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is detach the water supply. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be fairly troublesome because of the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipelines. When the supply pipelines have been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from turning throughout this process. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.

 

 

Mounting the Tub

Using the two wood boards under its feet, place the tub in the required setting. The wooden boards are practical in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the tub until the spirit level reviews degree.
To set up taps, fit the bottom of the outermost flexible tap adapter to the suitable supply pipe by making a compression join; after that do the exact same for the various other faucet.
Switch on the water system and check all joints as well as brand-new pipework for leakages and tighten them if required. Fill up the bath tub as well as also inspect the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bath tub should wait until the tub has been utilized at the very least when as this will certainly settle it into its last placement.

 

 

Suitable New Taps

If the tails of the new taps are plastic, then you will certainly require a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin making certain that the washing machines are in place between the faucet and also the sink. Safeguard the faucet in position with the manufacturer provided backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former type should be connected to the faucet finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Bath tub

In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to crack an inflexible seal, creating the water to pass through the wall surface between the bath as well as the tiling, resulting in problems with dampness and also feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your fixtures and installations. They are offered in tubes as well as cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of drenched paper or soft rope. Keep in mind to always load the tub with water before sealing, to permit the motion experienced when the tub remains in usage. The sealant can fracture rather early if you do not take into account this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof glue and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a serious reader on How to Install a Bathtub Yourself, I figured sharing that excerpt was worthwhile. Enjoyed our blog posting? Please share it. Help another person find it. Thanks a lot for your time spent reading it.

Book Maintenance